JSJR SEKWELE OPTICSPHOTONIC SOLUTIONS Request a Quote
HOME / Spectrometer Shutdown Flowchart

Spectrometer Shutdown Flowchart

Spectrometer Shutdown Flowchart - JR Sekwele Optical Networks & Photonic Group

Shut down the system

The system must not be shut down completely if you are not going to use it for a short time, such as overnight or over a weekend. This section describes how to shut down the system for a maintenance

Start up the system after a shutdown

Switch on the nitrogen flow at the tank, if it is off. Place the main power circuit breaker switch of the MS in the On (|) position. The forepump and the turbomolecular pumps are started. When the vacuum

Long Term Shut Down and Start Up Instructions

Shut down any accessories according to the instructions in their user guides. Aspirate distilled water for at least 5 minutes (flame analysis only). Turn off the instrument and disconnect the spectrometer

Agilent 5975 Series MSD

A mass spectrometer shutdown does not shut off the flow of carrier gas. As a result, hydrogen may slowly accumulate in the mass spectrometer. Introduction1 5975 Series MSD Operation Manual for

5975 Series MSD Troubleshooting and Maintenance Manual

This flow may be more than some mass spectrometers can pump away, resulting in the accumulation of hydrogen in the mass spectrometer. If the mass spectrometer is shut off at the same time, the

User Manual SX20 Stopped Flow Spectrometer

This document is intended to inform the operator of Applied Photophysics‟ SX20 stopped-flow spectrometer on its design, installation and operation. The information in this document is subject to

5975 Series MSD Operation Manual

A mass spectrometer shutdown does not shut off the flow of carrier gas. As a result, hydrogen may slowly accumulate in the mass spectrometer. Introduction1 5975 Series MSD Operation Manual 21

What is the proper shutdown procedure for single / triple quad

To vent the mass spectrometer and power off before a scheduled power outage. Vent the mass spec by selecting the vent option in the tune page. Navigate to the diagnostics tab in the tune page and

Standard operating procedure for operating JEOL EPR spectrometer

ESR Instrument : JEOL Japan Qband/X Band ESR Spectrometer Model - JES FA-200E Accessories used : OD ESR tubes

Venting and Shutting Down your Single or Triple Quadrupole LC/MS

Follow the entire shutdown procedure. Warning: The spray shield and related spray chamber components are likely to be hot. Do not touch them until they have cooled to a safe temperature for

Long Term Shut Down and Start Up Instructions

Raise the spectrometer cover. The dewar access hole is on the right rear of the detector compartment cover. Detector compartment cover Dewar fill hole raise spectrometer cover to access Figure 1.

Turn off your Single Quadrupole LC/MS System Using OpenLab CDS

Spray chamber voltages, the drying gas heater, the nebulization gas flow, the detector, and other specific lens voltages are all turned off. The drying gas flow is set to standby. If the APCI source is

Exactive GC Mass Spectrometer

Exactive GC Mass Spectrometer - Shutdown, Startup, and Reset Procedure Last updated Aug 12, 2025 Save as PDF Table of contents Description: Environment: Attachment (s):

Comprehensive Shutdown Protocols for Chromatographic, Mass

Proper shutdown procedures are essential not only for extending equipment lifespan but also for maintaining data reliability. This guide details standardized shutdown protocols for GC, LC, MS, and

Shut down the MS system completely for planned service or storage

Unplug the mass spectrometer''s power cord from the electrical outlet. CAUTION Do not disconnect the power supply cord from the MS while the other end is still plugged into the electrical outlet. TIP When

Start up the system after a shutdown

To start up the mass spectrometer after it has been shut down (and vented), you must do the following: Start up the instrument Set up conditions for operation Start up the system Procedure Make sure that

A Complete Guide to Shutting Down Analytical Instruments

For holidays or extended breaks, our guides are here to support you in powering down your LC/MS, GC/MS, and Spectroscopy instruments safely

How to vent and shut down a quadrupole MS system controlled by

OBJECTIVE: Safely shut down the LCMS system in preparation for a planned power outage. PROCEDURE: Turn off LC flow into the source. Put the MS into Standby mode. Turn off all gas

Agilent 7000 Series Triple Quad GC/MS

A mass spectrometer shutdown does not shut off the flow of carrier gas. As a result, hydrogen may slowly accumulate in the mass spectrometer. Mass spectrometer automated shutoff valves closed

Shut down the system

An instrument that is shut down still consumes nitrogen because the vent valve is connected to the nitrogen supply of the laboratory. Keeping on the nitrogen flow prevents humidity from contaminating

Major liquid mass spectrometers on|off procedure_

After shutting down the liquid phase, the mass spectrometer enters standby mode, opens the software “System Control” module, clicks on “Auto Shutdown,” and waits for the mass spectrometer heating

Shutdown Procedures of LC and LCMS Products

Some vendors may not have stock because they were shutdown (or still shutdown) or there is a spike in demand from labs coming back online. Call your vendor NOW to check inventory/manufacturing of

Agilent AA Spectrometer Shutdown Guide

1 Shut down any accessories according to the instructions in their user guides. 2 Aspirate distilled water for at least 5 minutes (flame analysis only). 3 Turn off the

What is the proper shutdown procedure for single / triple quad

OBJECTIVE: To vent the mass spectrometer and power off before a scheduled power outage. PROCEDURE: Open tune page and shutdown gases and place MS in standby Vent the mass spec

Industry Updates

Still Have a Technical Question?

Our photonic engineering team can help you select the right PLC splitter for your network.

Ask Our Team